A500 Rotary Sensor


ANZEx Approved Intrinsically Safe sensors
for Hazardous Gas, Dust and Mining Environments

Available in any travel from 16° to 160°



The A500 RIPS® (Rotary Inductive Position Sensor) is ANZEx approved for use in potentially explosive mining, gas/vapour and dust environments. It is designed for industrial and scientific feedback applications and is ideal for OEMs seeking good sensor performance for arduous applications in hazardous areas.
The A500, like all Positek sensors, is supplied with the output calibrated to the angle required by the customer, between 16 and 160 degrees and with full EMC protection built in. The sensor provides a linear output proportional with angle of rotation. There is a machined registration mark to identify the calibrated mid point. Overall performance, repeatability and stability are outstanding over a wide temperature range. The A500 has long service life and environmental resistance with a rugged stainless steel body, flange and shaft. The flange or servo mounting options make the sensor easy to install, it also offers a range of mechanical options. Environmental sealing is to IP67.


Positek intrinsically safe sensors are designed to be used with a galvanically isolated amplifier .  Approved galvanic isolation amplifiers (A005) are available from Positek; there is a choice of 0.5-9.5V or 4-20mA transmission outputs.

The sensor can be installed with a cable length up to 150m between the sensor and the amplifier.

Specification

Intrinsic Safety

 

ANZEx approval

ANZEx approved to Ex ia I/IIC T4 (Ta = -40°C to +80°C) Suitable for all areas (including mining), can be used in areas with continuous, long or frequent periods of exposure to hazardous gas (Zones 2 to 0) and dust (Zone 20), equipment remains energised. Protection class ia, denotes intrinsically safe for all zones Apparatus group IIC: suitable for IIA, IIB and IIC explosive gases. Temperature class T4: maximum surface temperature under fault conditions 135°C. Ambient temperature range extended to -40°C to +80°C. The sensor is certified to be used with up to 150m of cable with parameters not exceeding:- Capacitance = 550 nF total, Inductance = 0.66uH/m Approval only applies to the specified ambient temperature range and atmospheric conditions in the range 0.80 to 1.10 Bar, oxygen <=21%.

Galvanic Isolation Amplifier

It is imperative Positek® intrinsically safe sensors be used in conjunction with a galvanic barrier to meet the requirements of the product certification. The Positek A005 Galvanic Isolation Amplifier is purpose made for Positek IS sensors making it the perfect choice. Refer to the A005 datasheet for product specification and output configuration options.
Sensor input parameters are:-
Ui = 11.4V Ii = 0.2A Pi = 0.51W
Ci = 1.56ìF Li = 0.15mH (cable option/s)
Ci = 1.01ìF Li = 0.05mH (connector option/s)

Sensor Specification

 

Dimensions

 

Body Diameter

35mm

Body Length (to seal face)

44mm

Shaft

15mm, OD 6mm

 

For full mechanical details see drawing

Measurement range

Any angle from ±10° to ±80°

Independant Linearity

<±0.25% up to 100° @ 20°C
<±0.1% available on request

Temperature Coefficient

<±0.01%/°C Gain & <±0.01%FS/°C Offset

Output characteristics

 

Resolution

Infinite

Noise

<0.02% FSO

Shaft Torque

<20mNm Static

Frequency Response

>10KHz (-3dB)

 

 

Temperature Limits

 

Operating

-40 to + 80°C

Storage

-40 to + 125°C

EMC Performance

 

Susceptibility

EN 61000-6-2

Radiated

EN 61000-6-3

 

 

Vibration

IEC 68-2-6: 10g

Shock

IEC 68-2-29: 40 g

MTBF

350,000 hrs 40°C Gf

Sealing

IP67

 

 

Electrical Connections

Screened 3 core cable or integral connector

Detailed Dimensions

Refer to drawings below. Other options available.

Barrier

 

Outline

Click for pdf
Request AutoCAD Drawing
Datasheet Click for pdf
Installation Sheet Click for pdf


Preferences

Positek offers a range of options for its standard sensors.
Each sensor is manufactured to suit each customer's preferences.
If your requirement is outside the options given below,
Positek can modify/ redesign a sensor to suit your specific requirement.
Standard options are available as below:

 

Measurement range:

Factory set to any angle from ±8° to ±80° in increments of 1°
For example, if your application requires 90° measurement
then Positek will manufacture the sensor specifically for this angular range.
The sensor will measure 90° however will still rotate through 360°.




Connector/Cable Options:

Option code
Connector IP67, M12 - 4 pin
J
Cable, Gland IP67, M12 - 4 pin
L
Cable length - The standard length of cable supplied with a Positek position sensor is 50cm although you can specify any length you require, up to a maximum of 15000cm.
Specified in cm after the L
e.g. L200 for 200cm cable from axial cable gland


Mounting Options:
Option code
Flanged housing
blank
Servo mount
P

<+/-0.1% FSO Linearity error (100° max)
Z650

 

Click Here For Approved Galvanic Isolation Amplifier Options


 

 

Free Design Service

If you need a position sensor that is outside the scope of the above options to suit your installation requirement or specification, Positek will be happy to modify or create a new design to suit your needs


Contact Positek Technical Department - Click Here


 

Get Price


Back To Top

Home Page Quality | Products | Part Number Coding | Case Studies |

| Help Desk | Enquiries | Distributors | How to find us |

 

   


Company logo

 

Home

Products

Enquiries

How To Buy

Quality

Product Index

Support

ATEX logo

IECEx

iso 9001:2000 logo


  Positek Limited

L6 The Link   Andoversford Industrial Estate   Cheltenham   Glos GL54 4LB   UK
Tel: +44 (0) 1242820027   Fax: +44 (0)1242 820615   Email: Sales@Positek.com

Registered in England Number: 2746707 - VAT Registration Number: GB 618 0533 56